Product Description
The cost-efficient fixing for flexible use in non-cracked concrete
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside.
Advantages
- The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
- The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
- The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
- Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
- The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.
Available Product Variants
| Variant | ETA-approval | Drill diameter | Min. drill hole depth for through fixings | Anchor length |
|---|---|---|---|---|
| FBN II 6/5 | Yes | 6 [mm] | 45 [mm] | 50 [mm] |
| FBN II 6/10 | Yes | 6 [mm] | 50 [mm] | 55 [mm] |
| FBN II 6/30 | Yes | 6 [mm] | 70 [mm] | 75 [mm] |
| FBN II 8/10 HDG | Yes | 8 [mm] | 66 [mm] | 71 [mm] |
| FBN II 8/30 HDG | Yes | 8 [mm] | 86 [mm] | 91 [mm] |
| FBN II 8/50 HDG | Yes | 8 [mm] | 106 [mm] | 111 [mm] |
| FBN II 8/70 HDG | Yes | 8 [mm] | 126 [mm] | 131 [mm] |
| FBN II 10/10 HDG | Yes | 10 [mm] | 78 [mm] | 86 [mm] |
| FBN II 10/30 HDG | Yes | 10 [mm] | 98 [mm] | 106 [mm] |
| FBN II 10/50 HDG | Yes | 10 [mm] | 118 [mm] | 126 [mm] |
| FBN II 10/100 HDG | Yes | 10 [mm] | 168 [mm] | 176 [mm] |
| FBN II 12/10 HDG | Yes | 12 [mm] | 95 [mm] | 106 [mm] |
| FBN II 12/30 HDG | Yes | 12 [mm] | 115 [mm] | 126 [mm] |
| FBN II 12/50 HDG | Yes | 12 [mm] | 135 [mm] | 146 [mm] |
| FBN II 12/100 HDG | Yes | 12 [mm] | 185 [mm] | 196 [mm] |
| FBN II 16/25 HDG | Yes | 16 [mm] | 129 [mm] | 145 [mm] |
| FBN II 16/50 HDG | Yes | 16 [mm] | 154 [mm] | 170 [mm] |
| FBN II 16/100 HDG | Yes | 16 [mm] | 204 [mm] | 220 [mm] |
| FBN II 20/30 HDG | Yes | 20 [mm] | 165 [mm] | 187 [mm] |
| FBN II 6/10 R | Yes | 6 [mm] | 50 [mm] | 55 [mm] |
| FBN II 6/30 R | Yes | 6 [mm] | 70 [mm] | 75 [mm] |
| FBN II 8/5 K R | Yes | 8 [mm] | 51 [mm] | 55 [mm] |
| FBN II 8/10 R | Yes | 8 [mm] | 66 [mm] | 70 [mm] |
| FBN II 8/30 R | Yes | 8 [mm] | 86 [mm] | 90 [mm] |
| FBN II 8/50 R | Yes | 8 [mm] | 106 [mm] | 110 [mm] |
| FBN II 10/5 K R | Yes | 10 [mm] | 63 [mm] | 70 [mm] |
| FBN II 10/30 R | Yes | 10 [mm] | 98 [mm] | 105 [mm] |
| FBN II 10/10 R | Yes | 10 [mm] | 78 [mm] | 85 [mm] |
| FBN II 10/20 R | Yes | 10 [mm] | 88 [mm] | 95 [mm] |
| FBN II 10/50 R | Yes | 10 [mm] | 118 [mm] | 125 [mm] |
| FBN II 10/100 R | Yes | 10 [mm] | 168 [mm] | 175 [mm] |
| FBN II 12/5 K R | Yes | 12 [mm] | 75 [mm] | 84 [mm] |
| FBN II 12/10 R | Yes | 12 [mm] | 95 [mm] | 104 [mm] |
| FBN II 12/20 R | Yes | 12 [mm] | 105 [mm] | 114 [mm] |
| FBN II 12/30 R | Yes | 12 [mm] | 115 [mm] | 124 [mm] |
| FBN II 12/50 R | Yes | 12 [mm] | 135 [mm] | 144 [mm] |
| FBN II 12/100 R | Yes | 12 [mm] | 185 [mm] | 194 [mm] |
| FBN II 16/10 R | Yes | 16 [mm] | 114 [mm] | 128 [mm] |
| FBN II 16/25 R | Yes | 16 [mm] | 129 [mm] | 143 [mm] |
| FBN II 16/50 R | Yes | 16 [mm] | 154 [mm] | 168 [mm] |
| FBN II 20/30 R | Yes | 20 [mm] | 165 [mm] | 187 [mm] |
| FBN II 20/60 R | Yes | 20 [mm] | 195 [mm] | 217 [mm] |
| FBN II 8/5 K HDG | Yes | 8 [mm] | 51 [mm] | 56 [mm] |
| FBN II 10/5 K HDG | Yes | 10 [mm] | 63 [mm] | 71 [mm] |
| FBN II 12/5 K HDG | Yes | 12 [mm] | 75 [mm] | 86 [mm] |
| FBN II 16/15 K HDG | Yes | 16 [mm] | 104 [mm] | 120 [mm] |
| FBN II 16/15 K R | Yes | 16 [mm] | 104 [mm] | 118 [mm] |
Application and Permission
Applications
- Steel constructions
- Guard rails
- Consoles
- Ladders
- Cable trays
- Machines
- Staircases
- Gates
- Façades
Building materials
Approved for:
- Concrete C20/25 to C50/60, non-cracked
Also suitable for:
- Concrete C12/15
- Natural stone with dense structure
You can find detailed information on building materials in the registration document.
Permission
- ETA-07/0211
- ETA-07/0211
- ETA-18/0101
- DoP 0192
- DoP No. 0015
- DoP No. 0098
Assembly Instruction
Functionality
- The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions.
- Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut).
- When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall.
- The head embossing offers a simple control of the anchoring.
- In the case of series installation, we recommend using the FABS bolt anchor setting tool.
